Sample Size – RAD™ PaintStrip Paver/Stamped Concrete Stripping Gel
Sample Size Covers Roughly 8 Square Feet.
R-A-D™ PaintStrip is the right choice for almost any paint, paver sealer, or stamped concrete sealer stripping project. R-A-D™ PaintStrip is eco-friendly, works fast (starts working within 5 minutes), and removes up to 5 layers of most paints in 30-45 minutes, and up to 15 layers in 24 hours. R-A-D™ PaintStrip stays wet for 24+ hours, allowing you to strip larger areas without having to reapply.
When & Where to use RAD™ PaintStrip
R-A-D™ PaintStrip does not contain any hazardous methylene chloride or NMP. R-A-D™ PaintStrip is non-flammable, non-combustible, and practically odor free. R-A-D™ PaintStrip can be used on interior and exterior surfaces including brick, brick pavers, stamped concrete, concrete, plaster, stone, metal, fiberglass, and more. Additionally, R-A-D™ PaintStrip clings well to vertical surfaces.
R-A-D™ PaintStrip Removes
- Brick Paver Sealers that have turned white
- Stamped Concrete Sealers that have turned white
- Paints, Varnishes, Solid Acrylic Sealers
DO NOT use on drywall, rubber, plastic, or vinyl.
R-A-D™ PaintStrip for Concrete ADVANTAGES
- PROFESSIONAL STRENGTH Fast-Acting Paint Stripping Gel
- Removes up to 15 layers of water and solvent-based brick paver sealers, stamped concrete sealers, acrylic-based, varnish, stains, lacquers, and more in a single application
- Multi-Surface: Works on vertical and horizontal surfaces including wood, metal, masonry, and many more
- Stays Wet for 24+ Hours for Difficult Stripping Projects
- Eco-Friendly
- Non-Flammable & No Harsh Fumes
- No Methylene Chloride or NMP
Directions and Technical Info
Test Patch:
Before general use, test on a small area to determine compatibility, required dwell time, and coverage
for desired results. For an estimated 5 or less coats, scrape a section of the area with a stripping tool
after one hour of dwell time. If not easily down to wood after one hour, leave on longer and test again
hourly. For 10 – 15 coats of paint, cover with plastic and wait 24 hours to test. For best results, cover the
stripper with plastic and do not allow to dry.
DIRECTIONS:
- Shake well before use. Protect all areas not being stripped with plastic sheeting. Rubber gloves
and safety glasses are recommended for eye and skin protection. - Pour into a container and apply with a brush, roller (best applied with a 1 1/4” nap roller), or airless sprayer. Apply liberally – the stripper should cover the color of the stain. For best results and extended dwell times, cover stripper with plastic. Do not let stripper dry out, mist with water if you notice any dry areas. Refer to test area on dwell time before stripping. Test stripping a small area to ensure you are down to the substrate. If not, leave R-A-D™ PaintStrip on and let it do its job. R-A-D™ PaintStrip may or may not bubble. This will depend on the type of paint or sealer being removed. One gallon covers approximately 50-100 sq. ft. Best results are achieved when R-A-D PaintStrip is applied at temperatures between 60F and 80F.
- For best results, agitate with a stiff bristle brush and then remove by either scraping or pressure
washing. Always pressure wash at an angle so that the water jet acts as a chisel. - Let surface dry completely before refinishing. Clean all tools with soap and water.
- Dispose of paint or sealer waste in accordance with local, State, and Federal regulations.
COVERAGE:
R-A-D™ PaintStrip covers approximately 50-100 square feet per gallon of product. Coverage will vary on application method and substrate.
SAFETY CAUTION: See Full R-A-D™ PaintStrip SDS
Contains benzyl alcohol, monoethanolamine and surfactants. Prevent eye contact. Avoid contact with skin and clothing. Wear safety goggles and gloves during use. Wash with soap and water after use. Keep container closed when not in use. FIRST AID: EYES: Immediately flush with water for at least 20 minutes. If wearing contact lenses, remove and continue flushing with water. Seek immediate medical attention. SKIN: Rinse with soap and water. Remove contaminated clothing and launder before reuse. If irritation develops, seek medical attention. SWALLOWED: If swallowed, rinse mouth out with water and give 1 glass of water if person is alert. Do not induce vomiting. Immediately contact a poison control center, physician, or hospital emergency room for instructions.
KEEP OUT OF REACH OF CHILDREN. Max: voe g/L; Max Vapor Pressure of voe: 28.5 mm Hg. Non-photochemically Reactive. Less than 50% VOC. No Methylene Chloride or NMP I Eco-Friendly