NOW CONTAINS AN ANTIFUNGAL TO PREVENT MOLD, MOSS & ALGAE ON SEALER FILM
SB-1300 Joint Stabilizing Sealer is a water-based, single component, epoxymodified, enhancing sealer and joint sand stabilizer. The product can be used both inside and outside, on old and new pavements, sealing paving stones and stabilizing joint sand at the same time. It is the only sealer that can be applied immediately after paver installation, as it is breathable and will not trap the naturally occurring efflorescence. This breathability also decreases freeze-thaw damage and improves surface durability and ease of maintenance. SB-1300 Joint Stabilizing Sealer is solvent free and exceeds all VOC and EPA standards. The product is non-hazardous and has the consistency of water. It is milky white when applied and dries crystal clear, creating a finish that ranges from a matte finish to a satin sheen, depending on the surface. Cured sealer is freeze resistant to -60°F (-51°C) and is stable up to a temperature of 180°F (82°C).
Benefits:
- Fast Drying
- Breathable
- Sealer and Joint Sand Stabilizer
- Environmentaly Friendly
- Reduces Weed
Preparation:
The pavement surface should be clean and free from oil, dust and any loose material. If necessary, use SB-442 General Stain Remover to clean pavers (refer to label and data sheet for guidelines). The paver joints should be completely filled with dry, correctly graded jointing sand with the top level not exceeding the bottom of the chamfer or 1/8” below the surface on non-beveled or tumbled paver surface. A leaf blower is the recommended method to remove dust and fine sand particles from the surface and achieve the optimum joint sand height. Remove all visible efflorescence prior to sealer application; use SB-EffloOff if necessary (refer to label and data sheet for guidelines). Be sure surface is dry prior to application.
Application Information:
SB-1300 Joint Stabilizing Sealer should be flood coated to the pavement surface using a siphon pump, bulk sprayer or a handheld garden sprayer. Use coverage guidelines to determine the correct amount of material for the project. Flood joints to ensure proper sand penetration and stabilization and use a soft foam squeegee to direct excess material into the joints and to remove all excess material from the surface. Material coverage will depend on surface porosity, joint size and pavement usage. Care should be taken that no excess material is pooled on the surface. Clean all application equipment with water and do not allow material to dry in containers as removal becomes more difficult.
Coverage Per Gallon:
100-150 square feet depending on substrate porosity.
Which water based sealer do you recommend for a semi gloss but no wet look cal stone paver?
Surebond SB-7000:
https://www.concretesealerstore.com/sb-7000-gloss-joint-stabilizing-sealer-5-gallon.html
Thank you. Does SB 1300 enhance paver color without adding gloss or wet finish or I won’t notice any difference after I apply SB 1300? Hope answer to this will help me to decide which one to go with. Thanks
The SB-1300 does not enhance the appearance.
Any recommendation for Matt finish (enhance color) but no gloss or wet?
Wet look is enhancing the color. Look at SB-6000.
Yes but make sure it is one “flood” coat.
Is one coat enough for first time application ?
The SB-1300 will seal and help stabilize the joint sand. It does not change the appearance. If this is what you seek then yes this is your best option. Needs to be reapplied every 2 years. Nothing will last longer.
I would like to seal my concrete pavers here in central florida and based on my research think that sb-1300 would be my choice. Please tell me if you believe that to be my best choice in a water based sealer. How long should this product last if properly applied and do any of your concrete paver sealers have a noticeably longer life than the sb-1300?
Sb-1300 cures in a day and dries in 2-4 hours.
What is the cure time on SB1300?
Rain window before and after application?
What is the cure time? on SB1300. Rain window before and after
application?